Sony RM-VL610T Uživatelský manuál

4-117-855-11 (1)IntegratedRemoteCommander©2008 Sony CorporationRM-VL610TOperating Instructions

10Setting a Component Code bythe Search FunctionYou can find a code number available for acomponent that does not have one in the supplied“Component c

11Operating Your Componentswith the Remote CommanderWhen you operate a non-Sony component, makesure you set the component code first (page 8).Example:

12Programming Signals of AnotherRemote Control — LearningFunctionTo operate components or functions which do notwork even if you set a component code

13Example: To programme the H (Play) signal ofyour video cassette recorder to the VCR H(Play) button of the Commander1 Place the RM-VL610T head to hea

14If the SET indicator flashes five timesIt means that “learning” is incomplete. Repeat steps 4and 5.6 Repeat Steps 4 and 5 to “teach” functionsto oth

15Programming remote control signals tothe Component Select buttons andSystem Control buttonsYou can “teach” one operating procedure to aComponent Sel

162 While holding the desired ComponentSelect button pressed, press the button youwant to erase.When erasing of the “learned” function iscompleted, th

17To erase the learned function of the ComponentSelect button and System Control buttonsExample: To erase the function “learned” by theTV button1 Whil

18Notes on programming the signals for anair-conditionerAbout seasonal adjustmentsIf you change the settings of the air-conditioner forthe season, you

19Advanced FeaturesControlling the Volume of VisualComponents Connected to anAudio SystemThe Commander is factory preset based on theassumption that y

2FeaturesThe RM-VL610T Remote Commander providescentralised control of all your AV componentsfrom a single remote commander and saves thetrouble of op

20To set only the audio components’ volumecontrols to AMPPress 2 – while holding % pressed.Only AMP lights up when you press thesebuttons, and then tu

21Executing a Series of Commands— System Control FunctionsWith the System Control function, you canprogramme a series of operating commands, andexecut

22Example: To programme the procedure above tothe SYSTEM CONTROL 2 button1 Press and while holding SET, press theSYSTEM CONTROL 2 button.The SET indic

23Programming a Series ofCommands on the ComponentSelect ButtonsAs with the SYSTEM CONTROL buttons, you canalso programme a series of operating comman

24To clear programmed commands1 Press and while holding SET, press andhold for more than 3 seconds theComponent Select button you want toclear.Notes•Y

25While the Hold function is on, no function canbe operated. (The SET indicator and theComponent Select button currently selectedflash twice.)To unloc

26Erasing All Settings— To reset the Commander toits factory settingsYou can erase all remote control signalsprogrammed by the “learned“ function to r

27Additional InformationPrecautions•Do not drop the unit or give a shock to the unit, orit may cause a malfunction.•Do not leave the unit in a locatio

28TroubleshootingIf you have problems setting up or using the Remote Commander, first check the batteries (page 6), thencheck the items below.Remedy•

29SymptomAll Component Select buttons flash twice.After programming the Power-On command of acomponent, pressing that Component Select button doesnot

Startup GuideThis guide shows you how to set the Remote Commander to operate your components.First, find the four-digit component code number for your

30Using FastextWith Fastext you can access pages with one keystroke.When a Fastext page is broadcast, a colour-codedmenu will appear at the bottom of

31KEY DISPLAYqd134qh1 – 9, 0, - , ENT,1 –, 2 –w; (DISPLAY)qf a(ANT/SW)1t(INPUT SELECT)waMENUws Vws vws bws Bws OKqsmqsHqsMqsREC zqsxqsXqjPROG +

32* In order to avoid recording by mistake, the z RECbutton does not work by itself.KEY DISPLAYqd13qh 1 – 9, 0, ENT4-/-- (+10)2DIGITAL(AUDIO)0GUIDEqaR

33KEY DISPLAYqd1qsmqsHqsMqsREC zqsxqsX31 – 9, 0qhENTqs>qs.DATFUNCTIONTo turn on and off.To rewind.To play.To fast-forward.To record, press H while

34IndexA, BBatteries 6C, DChanging 16Clearing/Changinglearned signal 16, 17Power-On command 20Code numbers 8, 10Component Select buttonsassigning

Printed in China

1 Place the RM-VL610T head to head withyour VCR’s remote control.2 Set the RM-VL610T for “learning” mode.Press and hold SET for at least 3 secondsunti

5Table of ContentsStartup Guide ... 3Getting StartedInstalling the Batteries ...

6Getting StartedInstalling the BatteriesSlide open the battery compartment lid and inserttwo R6 (size AA) batteries. Be sure to match up the+ and – in

7Location of ControlsAbout tactile dotsThe number 5 button, the H button and PROG + button each have a tactile dot for ease of use.* Note on the 2 +/–

8Example: To set up a Philips’ TV1 See the tables in the supplied “Componentcode numbers,” and find the four-digitcomponent code number for the desire

9Notes• If you press a component code number that is not on thetable in the supplied “Component code numbers,” or ifyou press a button in the wrong or