Sony M-470 Uživatelský manuál stáhnout pdf

2-593-807-82 (1)

Operating Instructions

使用说明书

使用說明書（在背面）

M-575V/570V/475/470

Microcassette

™

Corder

Playing a Tape

1 Insert a cassette with the side to start playing facing the lid.

2 Select the tape speed to the same speed as that used for

recording.

3 Press n.

4 Turn VOL to adjust the volume. There is a tactile dot beside

VOL on to show the direction to turn up the volume.

At the end of the tape, playback stops and the unit turns off

automatically (Automatic shut-off mechanism). After the tape

has been wound or rewound, be sure to press Tx.

If you plug in headphones (not supplied) to the EAR jack, you

will get monaural output from both left and right channels.

To Press or slide

Stop playback/stop fast Tx

forward or rewind

Pause playback Slide >PAUSE in the direction of the

arrow. REC/BATT (M-575V/570V) or BATT

(M-475/470) lamp goes off.

To release pause

playback

, release

PAUSE*.

Fast forward** (FF) Slide FF/CUE m•M REW/REVIEW

toward FF/CUE m during stop.

Rewind** (REW) Slide FF/CUE m•M REW/REVIEW

toward M REW/REVIEW during stop.

Search forward during Keep FF/CUE m•M REW/REVIEW

playback (CUE) pushed toward FF/CUE m during playback

and release it at the point you want.

Search backward during Keep FF/CUE m•M REW/REVIEW

playback (REVIEW) pushed toward M REW/REVIEW during

playback and release it at the point you want.

Start recording during z

playback

* >PAUSE will also be automatically released when Tx is pressed

(stop-pause-release function).

**If you leave the unit after the tape has been wound or rewound, the

batteries will be consumed rapidly. Be sure to press Tx.

Note

If the tape is completely rewound while searching backward during

playback (REVIEW), the FF/CUE m•M REW/REVIEW switch may

not return to the center position when you release the switch. In this case,

push back the switch to the center to start playback.

Precautions

On power

• Operate the unit only on 3 V DC.

For AC operation, use the AC power adaptor recommended for the

unit. Do not use any other type. For battery operation, use two R03 (size

AAA) batteries.

On the unit

• Use only the (standard microcassettes) with this unit.

Non-standard cassettes cannot be used because their “L” dimension

(see illustration) is different.

Standard Non-standard

• Do not leave the unit in a location near heat sources, or in a place

subject to direct sunlight, excessive dust or mechanical shock.

• Should any solid object or liquid fall into the unit, remove the batteries

or disconnect the AC power adaptor, and have the unit checked by

qualified personnel before operating it any further.

• Keep personal credit cards using magnetic coding or spring-wound

watches, etc. away from the unit to prevent possible damage from the

magnet used for the speaker.

• When you do not use the unit for long, remove the batteries to avoid

damage caused by battery leakage and subsequent corrosion.

• If the unit has not been used for long, set it in the playback mode and

warm it up for a few minutes before inserting a cassette.

If you have any questions or problems concerning your unit, please

consult your nearest Sony dealer.

Troubleshooting

Should any problem persist after you have made these checks,

consult your nearest Sony dealer.

You cannot close the cassette compartment lid.

t The cassette is being inserted in the wrong way.

t n has been already pressed.

t The cassette is not being inserted completely.

The unit does not operate.

t The batteries have been inserted with incorrect polarity.

t The batteries are weak. Replace both batteries with new

ones.

t>PAUSE is slid in the direction of the arrow.

t The AC power adaptor is not firmly connected.

t The unit will not run on dry batteries if the AC power

adaptor is left plugged into the DC IN 3V jack even

though you disconnect the AC power adaptor from the

power source.

Recording cannot be made.

t There is no cassette in the cassette compartment.

t The tab on the tape has been removed. To reuse the tape

for recording, cover the tab hole with adhesive tape.

t The batteries are weak. Replace both batteries with new

ones.

Recording is interrupted.

t The VOR switch is set to ON. When you do not use VOR,

set it to OFF (M-575V/570V only).

Recording cannot be erased completely.

t The head is contaminated. See “Maintenance”.

Playback cannot be made.

t The tape has reached the end. Rewind the tape.

No sound comes from the speaker.

t The earphone is plugged in. Unplug it.

t The volume is turned down completely.

The sound drops out or comes with excessive noise.

t The volume is turned down completely.

t The batteries are weak. Replace both batteries with new

ones.

t The head is contaminated. See “Maintenance”.

t Direct placement of the cassette tape on the speaker

resulted in magnetization and deteriorated tonal quality.

t Use the unit away from radiowave-emitting devices such

as cellular phones.

Tape speed is too fast or too slow or the sound is

distorted in the playback mode.

t Improper setting of the TAPE SPEED switch. Set it to the

same speed as that used for recording.

t The batteries are weak. Replace both batteries with new

ones.

During CUE/REVIEW the tape stops or does not run.

You cannot fast-forward or rewind.

t The batteries are weak. Replace both batteries with new

ones.

Maintenance

To clean the tape head and path

Press n and wipe the head, capstan and the pinch roller with a

cotton swab, moistened with alcohol every 10 hours of use.

To clean the exterior

Use a soft cloth slightly moistened in water. Do not use alcohol,

benzine or thinner.

Specifications

Tape

(normal position type)

Recording system

2-track 1-channel monaural

Speaker

Approx. 3.6 cm dia.

Tape speed

2.4 cm/s, 1.2 cm/s

Frequency range

300 - 4 000 Hz (with TAPE SPEED switch at 2.4 cm/s)

Output

Earphone jack (minijack/monaural) for 8 - 300 Ω earphone

Power output (at 10% harmonic distortion)

M-575V/570V: 450 mW

M-475/470: 250 mW

Power requirements

3 V DC batteries R03 (size AAA) × 2/External DC 3V power sources

Dimensions (w/h/d) (incl. projecting parts and controls)

M-575V/570V: Approx. 60.2 × 110.8 × 23.2 mm

M-475/470: Approx. 60.2 × 110.8 × 22.3 mm

Mass (main unit only)

M-575V/570V: Approx. 104 g

M-475/470: Approx. 97 g

Supplied accessories

Microcassette tape MC-30 (1) (M-570V/470 for the United States and

Europe only, M-475 for Europe, Asia, Central and South America and

the Middle and Near East only)

Microcassette tapes MC-30 (2) (M-470 for Canada only)

Microcassette tapes MC-30 (3) (M-575V for Canada and Europe only

and M-475 for the United States only)

Batteries (2) (M-570V for the United States only, M-575V for Canada

and Europe only, M-470 for the United States and Canada only and

M-475 for the United States and Europe only)

Design and specifications are subject to change without notice.

English

WARNING

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

About This Manual

The instructions in this manual are for 4 models.

The M-570V is

the model used for illustration purposes.

Their differences are shown in the table below:

M-575V/570V M-475/470

Tape counter a —

BATT lamp — a

REC/BATT lamp a —

VOR a —

a: provided or supplied

—: not provided or not supplied

There is no difference between M-575V and M-570V and between M-

475 and M-470 except for the supplied accessories.

M-575V consists of M-570V Microcassette recorder and accessories.

For information about the supplied accessories, see “Specifications” of

this manual.

Preparing Power Sources

Choose one of the following power sources.

Dry Batteries

Make sure that nothing is connected to the DC IN 3V jack.

1 Open the battery compartment lid.

2 Insert two R03 (size AAA) batteries with correct polarity and

close the lid.

To take out the batteries

To attach the battery compartment lid if it is

accidentally detached

When to replace the batteries

Replace the batteries with new ones of the same kind when the

REC/BATT (M-575V/570V) or BATT (M-475/470) lamp dims.

Notes

• The unit will play back normally for a while, even after the REC/BATT

(M-575V/570V) or BATT (M-475/470) lamp flashes. However, replace

the batteries as soon as you can. Otherwise, the built-in speaker may

emit a loud noise and recordings may not be made correctly.

• In the following cases you do not need to replace the batteries:

– if the REC/BATT (M-575V/570V) or BATT (M-475/470) lamp flashes

with the playback sound when you turn up the volume.

– if the REC/BATT (M-575V/570V) or BATT (M-475/470) lamp lights

momentarily when the tape starts running or at the end of the tape.

– if the REC/BATT (M-575V/570V) or BATT (M-475/470) lamp flashes

during FF/REW or CUE/REVIEW.

Battery life* (Approx. hours)

Batteries M-575V/570V M-475/470

Recording Playback** Recording Playback**

Sony alkaline 17 9.5 17 10

LR03 (SG)***

Sony manganese 6.5 3.0 6.5 3.5

R03 (SB)

* Measured valued by the standard of JEITA (Japan Electronics and

Information Technology Industries Association) (Using a Sony

Microcassette)

** Using a tape on which music has been recorded is played at volume

setting 7 using speaker

***When using Sony LR03 (SG) alkaline dry batteries (produced in Japan)

Note

The battery life may be shorter depending on the operating condition, the

surrounding temperature and battery type.

For maximum performance we recommend that you use

alkaline batteries.

House current

Connect the AC power adaptor to DC IN 3V and to the mains.

Use the AC-E30HG* AC power adaptor (not supplied).

Do not use any other AC power adaptor.

Notes

• Specifications for AC-E30HG vary for each area. Check your local

voltage and the shape of the plug before purchasing.

• Do not touch the AC power adaptor with wet hands.

• Connect the AC power adaptor to an easily accessible mains. Should

you notice an abnormality in the AC power adaptor, disconnect it from

the mains immediately.

* For customers in Taiwan

AC-E30HG is not commercially available in Taiwan.

Recording

You can record right away with the built-in microphone.

1 Press the reset button of the tape counter (M-575V/570V

only).

2 Press Tx and insert a standard microcassette with the side

to start recording facing the lid.

3 Select the desired tape speed.

2.4 cm for optimum sound (recommended for normal use):

A 30-minute recording can be made using both sides of the

MC-30 microcassette (for supplied accessories, see

“Specifications”). There is a tactile dot on this side.

1.2 cm for longer recording time: A 60-minute recording can

be made using both sides of the MC-30 microcassette (for

supplied accessories, see “Specifications”).

4 Set VOR to OFF (M-575V/570V only).

If you set VOR to ON, the unit automatically starts

recording the sound and pauses when there is no sound

(you can save tapes and batteries).

When the sound is not loud enough, set it to OFF, or the unit

may not start recording.

5 Press z.

n is pressed simultaneously and recording starts.

While the tape runs, the REC/BATT lamp lights and flashes

depending on the strength of the sound (M-575V/570V

only).

Recording level is fixed.

At the end of the tape, recording stops and the unit turns off

automatically (Automatic shut-off mechanism).

To Press or slide

Stop recording Tx

Pause recording

Slide >PAUSE in the direction of the arrow.

To release pause recording, release

PAUSE*.

Start recording during z during playback (the unit enters the

playback recording mode)

Review the portion just Push up FF/CUEm•MREW/REVIEW

recorded toward MREW/REVIEW during the

recording. Release the button at the point to

start playback.

Take out a cassette Tx

* >PAUSE will also be automatically released when Tx is pressed

(stop-pause-release function).

Note

Select the 2.4 cm tape speed for recording, if you play back the recorded

tape with another unit. Otherwise, the sound quality may be changed.

Notes on VOR (Voice Operated Recording) (M-575V/570V

only)

• The VOR system is affected by the environmental recording conditions.

When you use the system in a noisy place, the unit will stay in the

recording mode. If the sound is too soft, on the contrary, the unit will

not start recording. If you cannot get the results you want, set it to OFF.

• The VOR system may not record the beginning of the sound you want

to record because it starts recording only after it catches the sound. For

an important recording, set it to OFF.

To monitor the sound

Connect an earphone (not supplied) firmly to the EAR jack. The

monitor volume cannot be adjusted by VOL.

To prevent a cassette from being accidentally recorded

over

Break off and remove the cassette tabs. To reuse the cassette for

recording, cover the tab hole with adhesive tape.

Insert the

batteries with

correct polarity.

Polarity of the plug

to the mains

Approx. 5 mm

Only standard microcassettes have a

small indention of side A.

Approx. 2.5 mm

AC power adaptor

(not supplied)

Head

Pinch roller

Capstan

> PAUSE

EAR

VOR (M-575V/

570V only)

Microphone

FF/CUE m•

M REW/REVIEW

* The button/switch has a tactile dot.

Tape counter

(M-575V/570V only)

REC/BATT (M-575V/

570V)

BATT (M-475/470)

VOL*

Tape counter reset

button (M-575V/

570V only)

TAPE SPEED*

VOL*

>PAUSE

FF/CUE m•

M REW/REVIEW

EAR

* The button/switch has a tactile dot.

TAPE SPEED*

REC/BATT (M-575V/

570V)

BATT (M-475/470)

Printed on 100% recycled paper using VOC (Volatile Organic

Compound)-free vegetable oil based ink.

索尼公司

中文（简）

警告

为防火灾或触电危险，切勿让机器暴露于雨中

或潮湿处。

关于本手册

本手册中的说明适用于4种型号。在此以M-570V型号为图例

进行说明。

下表为各型号的区别：

M-575V/570V M-475/470

磁带计数器 a —

BATT 指示灯 — a

REC/BATT 指示灯 a —

VOR a —

a：提供或附带

—：未提供或附带

M-575V 和 M-570V 之间以及 M-475 和 M-470 之间除随机附件外，没

有其他区别。

M-575V 由 M-570V 微型卡带录音机及附件组成。

有关随机附件的内容，请参见本手册中的“规格”。

准备电源

操作时，有下列电源可供选用。

干电池

要以干电池操作时，DC IN 3V 插孔里不可连接任何电线。

1 打开电池室盖。

2 装入两个 R03（AAA，7 号）电池，装时须按照正确极性方向

装入，然后盖上盖子。

要取出电池时

电池室盖意外掉落时请将其装上

什么时候需要更换电池

REC/BATT(M-575V/570V)或 BATT(M-475/470)灯暗淡

时，请用相同型号的新电池予以更换。

注

• 即使REC/BATT(M-575V/570V)或BATT(M-475/470)灯起闪烁之后，

机器仍可正常地播放一段时间，但是必须尽快更换电池。如果不换电池，

内置扬声器会发出很大的噪音，可能无法正常录音。

• 如下状况时，并不必更换电池：

– 调高音量时，如果随播放声而 REC/BATT(M-575V/570V)或 BATT

(M-475/470)灯起闪烁。

– 当开始走带或到达磁带末端时：REC/BATT(M-575V/570V)或BATT

(M-475/470) 灯亮了一下。

– FF/REW（快进／重绕）或 CUE/ REVIEW（提示／检阅）操作中，如

果 REC/BATT(M-575V/570V)或 BATT(M-475/470)灯起闪烁。

电池寿命 *（大概小时数）

电池 M-575V/570V M-475/470

录音放音 ** 录音放音 **

Sony 碱性电池 17 9.5 17 10

LR03 (SG)***

Sony 锰性电池 6.5 3.0 6.5 3.5

R03 (SB)

*按JEITA（Japan Electronics and Information Technology

Industries Association）标准测量的值（使用 Sony 微型磁带）

** 使用扬声器以音量设置 7 播放录有音乐的磁带

*** 当使用 Sony LR03 (SG)碱性干电池（日本制造）时

注

电池寿命可能因使用条件、环境温度和电池类型而异。

建议使用碱性电池以取得最佳性能。

家用电流

将交流电源适配器连接到DC IN 3V插孔和电源。请使用AC-

E30HG *交流电源适配器（未附带）。请勿使用任何其他类型的交

流电源适配器。

插头的极性

注

• AC-E30HG 的规格因地区而异。购买前请检查当地电压和插头的形状。

• 请勿用湿手碰触交流电源适配器。

• 请将交流电源适配器连接到便于操作的电源上。如发现交流电源适配器出

现异常，请立即从电源上断开交流电源适配器。

* 对于台湾用户

台湾地区不出售 AC-E30HG。

录音

可使用内置麦克风立即录音。

1 按磁带计数器的重设键（仅适用于 M-575V/570V）。

2 按Tx键，插入一个标准微型卡带，装时须使要录音之面对着

卡带室盖。

3 选择录音带速度。

音质最佳的速度为 2.4cm（平常请以此速度放音）：使用

MC-30 微型卡带（有关附件的内容，请参阅“规格”）的正反

两面可以进行 30 分钟的录音。

这面有一个触点。

要进行较长录音时的速度为 1.2cm：使用 MC-30 微型

卡带（有关附件的内容，请参阅“规格”）的正反两面可以进

行60分钟的录音。

4 把 VOR 开关设定在 OFF（仅适用于 M-575V/570V）。

若把VOR开关设定在ON，则录音机将在发出声音时自动

开始录音，没有声音时自动暂停下来（可以节省磁带及电池之

消耗）。

要录的声音若不够大，把 VOR 开关设定在 OFF，否则便

无法令录音机开始录音。

5 按 z 键。

n 即同时被按下而开始录音。录音带一开始卷动，REC/

BATT 指示灯便发亮并按照声音强弱而闪烁（仅适用于 M-

575V/570V）。

录音电平是固定的。

到达磁带末端时，录音停止并且本机自动关闭（自动关机机

制）。

要请

停止录音按 Tx 键

暂停录音把 >PAUSE 开关往箭头方向移动。

要取消暂停录音，请释放

PAUSE* 键

。

在放音之中直接开始录音在放音之中按压 z 键（录音机便进入录音状态）

查听刚录下的部分在录音之中，把 FF/CUEm•MREW/

REVIEW 键设定在 MREW/REVIEW 之处。

在录音带转到要收听的地方时放开按键。

取出录音带按 Tx 键

*按Tx 键时 >PAUSE 键也将自动释放（停止 - 暂停 - 释放功能）。

注

要播放以其他录音机录音的磁带时，把磁带速度设定在2.4cm之处。否

则会影响放音时的音质。

关于 VOR (Voice Operated Recording) 开关的注意事项

（仅适用于 M-575V/570V）

• VOR 系统受环境录音条件影响。当在嘈杂的地方使用该系统时，本机将

一直处于录音状态。如果声音太轻，本机也不会开始录音。如果不能获得

理想的效果，请将其设为 OFF。

• VOR 系统可能没有录下要录声音的开始部分，因为只有它捕获到声音后

才开始录音。对于重要的录音，请将其设为 OFF。

若要一面录音一面监听所录着的声音

在EAR插孔连接耳机（无附带）。监听器的音量是不能用VOL

调整的。

为防止所录的地方因重录而被误消掉

拆掉录音卡带盒背的录音防止保险片。要再以那盒卡带录音

时，在拆掉保险片的小洞，贴张胶带就行。

放音

1 把要放音之面对着卡带室盖，装入录音带。

2 把放音速度调整在和录音时一样速度之处。

3 按 n 键。

4 旋转VOL 调节音量。

VOL旁边有一个触点，用于显示方向以

调高音量。

到达磁带末端时，放音停止并且本机自动关闭（自动关机机

制）。磁带完全绕完或重绕完之后，请务必按 Tx 键。

如果把头戴耳机（无附带）接插到 EAR 插孔，则从左频道及

右频道都将听到单耳声输出。

要请

停止放音／停止快转或倒转

暂停放音

快速前转 **(FF)

快速倒转**(REW)

在放音之中向前寻找某段落

（CUE 功能）

在放音之中向后寻找某段落

（REVIEW 功能）

放音时开始录音

*按Tx 键时 > PAUSE 键也将自动释放（停止 - 暂停 - 释放功能）。

**若在录音带走到尽头，或被卷回起点以后离开录音机，则电池将很快就用

完，切记此时一定要按下 Tx 键才离开座位。

注

放音中，当往后寻找时，如果磁带完全绕完或重绕完了(REVIEW)，

当您释放 FF/CUEm•MREW/REVIEW 开关时，它可能不会返回中央

位置的。此时，请把它推回中央位置以开始放音。

使用前须知注意事项

电源须知

• 限用 3V DC 操作机器。

对于交流电操作，请使用推荐用于本机器的交流电源适配器。请勿使用任

何其他类型的适配器。对于电池操作，请使用两个R03（七号，AAA）电

池。

录音机

• 本机只可使用注有（标准微型卡带）的录音带。非标准

型的卡带本机不能使用，因为“L”尺寸不同（如图）。

标准型非标准型

• 不可把录音机放在热源附近，或直接受到阳光照射的地方，以及灰尘极多，

容易受震动之处。

• 如果有任何杂物或液体掉入录音机内部时，请取出电池或断开交流电源适

配器，由有资质的人员对录音机进行检查后方可继续使用。

• 不要把使用磁码的个人信用卡或发条手表等，放在录音机附近，以免受到

录音机里的扬声器磁性的影响，而损失功能。

• 若长期不使用录音机，请取出电池，以免电池溶液泄漏，损伤机体或腐蚀。

• 录音机若长期没使用，下一次要再使用时，先把录音机设定在放音状态，

使机器预热了几分钟，然后才插入录音带。

若对本机有任何疑问，请咨询最近的 Sony 经销店。

故障排除

若在经过自己进行下列检查调查以后，仍然不能使录音机恢复

正常的话，请向 Sony 经销店商量。

不能关闭卡带室盖。

t 录音带方向装反了。

t n 键已经被按下了。

t 录音带没有完全插入。

本机不工作。

t 电池装反了。

t 电池电量不足。请同时更换两个新电池。

t>PAUSE 往箭头方向移动了。

t 交流电源适配器未牢固连接。

t 将交流电源适配器插入DC IN 3V 插孔时，即使从电源上断

开了交流电源适配器，也无法用电池操作机器。

不能录音。

t 卡带室里没装录音带。

t 磁带上的防录保险片被拆掉了。要使磁带能重新录音，用胶

带覆盖保险片孔。

t 电池用完了。请用新电池更换两节旧电池。

录音中途停止。

t VOR开关被设为ON。当不使用 VOR时，请把它设为OFF

（仅适用于 M-575V/570V）。

以前的录音不能完全消除。

t 磁头脏了。参看“维修”。

不能播放。

t 磁带已到头了。重绕磁带。

扬声器没有声音。

t 已插入耳机。请将其拔出。

t 音量被调到最小。

声音跳音或噪音太大。

t 音量被调到最小。

t 电池电量不足。请同时更换两个新电池。

t 磁头脏了。参看“维修”。

t 把卡带放在扬声器上导致磁化以及声音质量劣化。

t 在远离无线电发射设备如手机处使用本机。

磁带速度太快或太慢或者放音模式时声音失真。

t TAPE SPEED开关的设定不正确。把它设在和该磁带录音

时相同速度之处。

t 电池电量不足。请同时更换两个新电池。

CUE/REVIEW（提示／检阅）中，磁带停止或不走动。

不能进行快进或重绕。

t 电池电量不足。请同时更换两个新电池。

维修

磁头及磁带通道之清洁

每使用过 10 小时以後，请以棉棒沾点酒精，擦拭磁头、输带

轴及压带胶轮。擦时，请先按 n 键。

机体外表的清洁

机体外表请以一稍微沾湿的柔软布块擦拭，不可使用酒精、汽

油或稀释剂。

规格

磁带

微型卡带（普通位置型）

录音方式

2 声轨，1 频道，单音

扬声器

直径约为 3.6cm

磁带速度

2.4cm ／秒，1.2cm ／秒

频率范围

300 － 4 000Hz（TAPE SPEED（磁带速度）开关设定为 2.4cm ／秒）

输出

耳机插孔（微型插孔／单声道），供 8 － 300Ω 耳机之用

功率输出（于 10% 谐波失真时）

M-575V/570V∶450mW

M-475/470∶250mW

电源

3V DC 电池 R03（AAA，7 号）×2 ／外部 DC 3V 电源

尺寸（宽／高／深）（包括突出部分及控制器）

M-575V/570V∶约 60.2×110.8×23.2mm

M-475/470∶约 60.2×110.8×22.3mm

重量（主机为限）

M-575V/570V∶约 104g

M-475/470∶约 97g

随机附件

微型卡带 MC-30 (1)（M-570V/470 仅提供给美国和欧洲，M-475 仅提

供给欧洲、亚洲、中美洲和南美洲以及中东和近东。）

微型卡带 MC-30 (2)（M-470 仅提供给加拿大。）

微型卡带 MC-30 (3)（M-575V 仅提供给加拿大和欧洲，M-475 仅提供

给美国。）

电池(2)（M-570V 仅提供给美国，M-575V仅提供给加拿大和欧洲，M-

470 仅提供给美国和加拿大，M-475 仅提供给美国和欧洲。）

本机设计及规格或有变更之处，恕不另行通知。

> PAUSE

EAR

VOR（仅适用于

M-575V/570V。）

麦克风

FF/CUE m•M

REW/REVIEW

*按钮／开关有一个触点。

磁带计数器（仅适用

于 M-575V/570V。）

REC/BATT (M-

575V/570V)

BATT (M-475/470)

VOL*

磁带计数器重设键

（仅适用于

M-575V/570V。）

TAPE SPEED*

VOL*

>PAUSE

FF/CUE m•M

REW/REVIEW

EAR

*按钮／开关有一个触点。

TAPE SPEED*

REC/BATT (M-

575V/570V)

BATT (M-475/470)

磁头

输带轴

压带胶轮

约 5mm

只有标准型

微型卡带的 A 面才有一个小刻号。

约 2.5mm

请按正确极性插入

电池。

按 Tx 键

把 >PAUSE 开关往箭头方向移动。

REC/BATT (M-575V/570V)或 BATT

(M-475/470)灯熄灭。

要取消暂停放音，请释放

PAUSE* 键

。

在停止状态下，把 FF/CUEm•MREW/

REVIEW 开关往 FF/CUEm 方向移动。

在停止状态下，把 FF/CUEm•MREW/

REVIEW 开关往 MREW/REVIEW 方向

移动。

在放音之中向下推FF/CUEm•MREW/

REVIEW 键往 FF/CUEm 方向移动，直

到找到所要寻找的地方才放开按键。

在放音之中向上推FF/CUEm•MREW/

REVIEW 键往 MREW/REVIEW 方向移

动，直到找到所要寻找的地方才放开按键。

按 z 键

至电源

交流电源适配器（未附带）

1 2

Shrnutí obsahu

Strany 1 - Microcassette

Strany 2 - 為防火災或觸電危險，切勿讓機器暴露於雨中

中文（繁）警告為防火災或觸電危險，切勿讓機器暴露於雨中或潮濕處。僅適用於台灣廢電池請回收關於本說明書本說明書中的說明適用於 4 種型號。在此以 M-570V 型號為圖例進行說明。下表為各型號的區別︰M-575V/570V M-475/470走帶計數器 a —BATT 指示燈 — aREC/BATT

Další dokumenty pro Diktafony Sony M-470

Zobrazit dokument Sony M-470 Uživatelský manuál

Sony M-470 Uživatelský manuál (2 stránky)

Komentáře k této Příručce

Žádné komentáře

Sony M-470 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Diktafony Sony M-470. Sony M-475 User manual Uživatelská příručka

Shrnutí obsahu

Další dokumenty pro Diktafony Sony M-470

Komentáře k této Příručce

Související produkty a manuály pro Diktafony Sony M-470